Added: Burnell Stoffel - Date: 23.10.2021 07:23 - Views: 19584 - Clicks: 5809
Please turn it on so that you can experience the full capabilities of this site. Aftermarket driving lights like spot lights and LED light bars offer the ultimate driving light solution for every vehicle. Find out how easy they are to install! Aftermarket driving lights like spotlights and LED light bars offer the ultimate driving light solution for every vehicle. From trucks and four-wheel drives right through to sports cars and family sedans. It is the responsibility of the owner of the vehicle to abide by the relevant laws and regulations.
Wiring them up doesn't have to be hard if you have the right tools and accessories. We recommend using a driving light harness which uses a simple plug-n-play de meaning all the hard work is already done and you don't need to spend hours wiring. The kit works by tapping into your cars headlight circuit and feeds the power from your high beam, right to your driving light.
You will also have the option to turn the light off completely using the included master switch. In New Zealand, extra driving lamps, fog lamps or work lamps must be fitted in a way that they do not:. In addition to these basic requirements, New Zealand has its own legislation covering the use and placement of additional lighting - including some specifics around LED light bars.
Make sure you check the requirements before you choose a location for your LED light bar. Additional light bars acting as high beam headlamps must be fitted as a pair only to the front of your vehicle, making a total of 2 original high beam headlamps and 2 additional light bars as high beam headlamps. These additional light bars must be connected to the main high beam switch.
This means a single centre mounted light bar is not legal and cannot be considered a headlamp. A non-standards compliant light bar, or a standards compliant light bar that is fitted as a single lamp might be classified as a work lamp.
Work lamps can be fitted in a wide range of combinations and with no legal limitations on. However, they cannot be wired into the headlights and can be switched on independently of all other lighting equipment. Work lamps are for Offroad use only and are illegal to use during onroad use. There are limits on the of lights that can function at any given time - refer to the NZTA for more info. You can drive with your LED light bars on when connected to the high beam only - refer to the NZTA to ensure that you aren't breaking the law. Be smart and don't drive around blinding other drivers and use your low beams as per the law when approaching other vehicles.
Still, these must be within specific legal requirements - refer to the NZTA website for information around what sort of LED headlight setup is suitable for road use on New Zealand ro. Disconnect the negative terminal from your vehicle's battery before commencing any further work. Find a suitable location to mount the relay and fuse, preferably on the inner guard using an existing bolt, or a self-tapping screw. Ensure that the wire for the fuse will easily reach the battery, and connect the ring terminal to the positive terminal.
Locate the back of your high beam headlight globe on the side closest to the relay, and remove the plug from the end. Choose the headlamp adaptor supplied in the kit which suits your plug, and connect this to the factory plug. Another end connects to your headlight globe, and the third end plugs into your new harness. Run the plug through an accessible grommet in the firewall through to the engine bay — by either making an incision in the grommet or poking through with a sharp object. Taping the plug to a long piece of fencing wire will help it through any tight places.
The single plug must be connected to the relay, and the ring terminal on this end needs to be connected to an earth. Either directly to the negative terminal of the battery, or to a bolt with bare metal contact to the body. Now with the plugs that connect to the lights, if you are using a light bar, only one of the plugs needs to be connected. The second plug can be taped up out of the way, or you could use this wire for an additional light bar. If you are wiring up spot lights, connect a plug to each light. If your light bar switches off and your high beams remain on, you have successfully wired in your own LED light bar.
How many LED light bars can I legally have? Can you drive with LED light bars on? Can you use a light bar as headlights? Step 1 - Mounting the light bar. Step 2 - Disconnect negative terminal. Step 4 - Finding your vehicle's headlamp wiring. The light bar needs to be triggered by activation of your high beam. Step 5 - Attaching the headlamp adaptor. These plugs will only fit one way. Step 6 - Mounting the switch. Now mount the switch in the cab locating it convenient to the driver. Step 7 - Running the wires through the firewall. Step 8 - Connecting the two harnesses.
Connect this plug to the one which comes off your relay. The final piece in the installation is the plugs for your light bar. Step 10 - Taping additional wiring away.
Step 11 - Reconnecting the negative terminal. Step 12 - Testing. The light bar should not illuminate until you flick on the high beam. Step 13 - Finished! Facebook Twitter Pinterest. Related Articles. Winching For Beginners — Ultimate Guide.Best way to hook up led light bar
email: [email protected] - phone:(304) 789-4744 x 6638
How to Install an LED Light Bar on a Vehicle